summaryrefslogtreecommitdiff
path: root/drivers/pinctrl/intel
AgeCommit message (Collapse)AuthorLines
2020-04-17pinctrl: cherryview: Add missing spinlock usage in chv_gpio_irq_handlerGrace Kao-0/+4
According to Braswell NDA Specification Update (#557593), concurrent read accesses may result in returning 0xffffffff and write instructions may be dropped. We have an established format for the commit references, i.e. cdca06e4e859 ("pinctrl: baytrail: Add missing spinlock usage in byt_gpio_irq_handler") Fixes: 0bd50d719b00 ("pinctrl: cherryview: prevent concurrent access to GPIO controllers") Signed-off-by: Grace Kao <grace.kao@intel.com> Reported-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Brian Norris <briannorris@chromium.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2020-04-13pinctrl: baytrail: Enable pin configuration setting for GPIO chipAndy Shevchenko-0/+1
It appears that pin configuration for GPIO chip hasn't been enabled yet due to absence of ->set_config() callback. Enable it here for Intel Baytrail. Fixes: c501d0b149de ("pinctrl: baytrail: Add pin control operations") Depends-on: 2956b5d94a76 ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-04-13pinctrl: sunrisepoint: Fix PAD lock register offset for SPT-HAndy Shevchenko-7/+8
It appears that SPT-H variant has different offset for PAD locking registers. Fix it here. Fixes: 551fa5801ef1 ("pinctrl: intel: sunrisepoint: Add Intel Sunrisepoint-H support") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-01-16pinctrl: tigerlake: Tiger Lake uses _HID enumerationMika Westerberg-297/+250
Turns out that Tiger Lake GPIO will be enumerated using _HID method where there is only a single ACPI device and multiple BARs so rework the driver to support that scheme instead. Fixes: c9ccf71fc807 ("pinctrl: intel: Add Intel Tiger Lake pin controller support") Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2020-01-16pinctrl: sunrisepoint: Add Coffee Lake-S ACPI IDMika Westerberg-0/+1
Intel Coffee Lake-S PCH has the same GPIO hardware than Sunrisepoint-H PCH but the ACPI ID is different. Add this new ACPI ID to the list of supported devices. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2020-01-09pinctrl: intel: Pass irqchip when adding gpiochipLinus Walleij-13/+13
We need to convert all old gpio irqchips to pass the irqchip setup along when adding the gpio_chip. For more info see drivers/gpio/TODO. For chained irqchips this is a pretty straight-forward conversion. Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2020-01-09pinctrl: intel: Add GPIO <-> pin mapping ranges via callbackLinus Walleij-13/+22
When IRQ chip is instantiated via GPIO library flow, the few functions, in particular the ACPI event registration mechanism, on some of ACPI based platforms expect that the pin ranges are initialized to that point. Add GPIO <-> pin mapping ranges via callback in the GPIO library flow. Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2020-01-09pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq ↵Hans de Goede-4/+4
pin to output Suspending Goodix touchscreens requires changing the interrupt pin to output before sending them a power-down command. Followed by wiggling the interrupt pin to wake the device up, after which it is put back in input mode. On Cherry Trail device the interrupt pin is listed as a GpioInt ACPI resource so we can do this without problems as long as we release the IRQ before changing the pin to output mode. On Bay Trail devices with a Goodix touchscreen direct-irq mode is used in combination with listing the pin as a normal GpioIo resource. This works fine, but this triggers the WARN in byt_gpio_set_direction-s output path because direct-irq support is enabled on the pin. This commit replaces the WARN call with a dev_info_once call, fixing a bunch of WARN splats in dmesg on each suspend/resume cycle. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2020-01-09pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pinsHans de Goede-1/+7
Suspending Goodix touchscreens requires changing the interrupt pin to output before sending them a power-down command. Followed by wiggling the interrupt pin to wake the device up, after which it is put back in input mode. On Bay Trail devices with a Goodix touchscreen direct-irq mode is used in combination with listing the pin as a normal GpioIo resource. This works fine, until the goodix driver gets rmmod-ed and then insmod-ed again. In this case byt_gpio_disable_free() calls byt_gpio_clear_triggering() which clears the IRQ flags and after that the (direct) IRQ no longer triggers. This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag to byt_gpio_clear_triggering(). Note that byt_gpio_clear_triggering() only gets called from byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded from the irq_valid mask by byt_init_irq_valid_mask(). Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2020-01-08pinctrl: sunrisepoint: Add missing Interrupt Status register offsetBoyan Ding-0/+1
Commit 179e5a6114cc ("pinctrl: intel: Remove default Interrupt Status offset") removes default interrupt status offset of GPIO controllers, with previous commits explicitly providing the previously default offsets. However, the is_offset value in SPTH_COMMUNITY is missing, preventing related irq from being properly detected and handled. Fixes: f702e0b93cdb ("pinctrl: sunrisepoint: Provide Interrupt Status register offset") Link: https://bugzilla.kernel.org/show_bug.cgi?id=205745 Cc: stable@vger.kernel.org Signed-off-by: Boyan Ding <boyan.j.ding@gmail.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Update summary in the driverAndy Shevchenko-4/+6
Reflect in the driver that it is now a pin control one. While here, update copyright years and authors. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Switch to pin control APIAndy Shevchenko-57/+13
When all preparations are done, we may switch to pin control API. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Add GPIO <-> pin mapping ranges via callbackAndy Shevchenko-0/+14
When IRQ chip is instantiated via GPIO library flow, the few functions, in particular the ACPI event registration mechanism, on some of ACPI based platforms expect that the pin ranges are initialized to that point. Add GPIO <-> pin mapping ranges via callback in the GPIO library flow. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Implement ->pin_dbg_show()Andy Shevchenko-0/+23
The introduced callback ->pin_dbg_show() is useful for debugging. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Add pin control operationsAndy Shevchenko-1/+314
Add implementation for: - pin control, group information retrieval: count, name and pins - pin muxing: - function information (count, name and groups) - mux setting - GPIO control (enable, disable, set direction) - pin configuration: - pull disable, up and down - any other option is treated as not supported. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Reuse struct intel_pinctrl in the driverAndy Shevchenko-24/+60
We may use now available struct intel_pinctrl in the driver. No functional change implied. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Add pin control data structuresAndy Shevchenko-2/+124
In order to implement pin control for Intel Lynxpoint, we need data structures in which to store and pass along pin, community and SoC data information. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Implement intel_gpio_get_direction callbackAndy Shevchenko-0/+11
Allows querying GPIO direction from the pad config register. If the pad is not in GPIO mode, return an error. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Implement ->irq_ack() callbackAndy Shevchenko-3/+14
Instead of playing tricks with registers in the interrupt handler, utilize the IRQ chip core for ACKing interrupts properly. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Move ownership check to IRQ chipAndy Shevchenko-6/+6
There is nothing wrong with requesting pin that owned by ACPI. The only difference is how interrupt status will be reflected. It means that in ACPI mode we may not use pin as GPIO-backed IRQ. Taking above into consideration, move the check from GPIO to IRQ chip callback. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Move lp_irq_type() closer to IRQ related routinesAndy Shevchenko-44/+44
Consolidate IRQ routines for better maintenance. While here, rename lp_irq_type() to lp_irq_set_type() to be in align with a callback name. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Move ->remove closer to ->probe()Andy Shevchenko-6/+6
Consolidate ->remove and ->probe() callbacks for better maintenance. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Extract lp_gpio_acpi_use() for future useAndy Shevchenko-2/+12
We may need this function for other features in the pin control driver. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Convert unsigned to unsigned intAndy Shevchenko-12/+12
Simple type conversion with no functional change implied. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Switch to memory mapped IO accessorsAndy Shevchenko-44/+44
Convert driver to use memory mapped IO accessors. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Keep pointer to struct device instead of its containerAndy Shevchenko-7/+7
There is no need to keep pointer to struct platform_device, which is container of struct device, because the latter is what have been used everywhere outside of ->probe() path. In any case we may derive pointer to the container when needed. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Relax GPIO request rulesAndy Shevchenko-3/+11
A pin in native mode still can be requested as GPIO, though we assume that firmware has configured it properly, which sometimes is not the case. Here we allow turning the pin as GPIO to avoid potential issues, but issue warning that something might be wrong. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Assume 2 bits for mode selectorAndy Shevchenko-2/+4
New generations can use 2 bits for mode selector. Update the code to support it. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Use standard pattern for memory allocationAndy Shevchenko-1/+1
The pattern foo = kmalloc(sizeof(*foo), GFP_KERNEL); has an advantage when foo type is changed. Since we are planning a such, better to be prepared by using standard pattern for memory allocation. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Use %pR to print IO resourceAndy Shevchenko-2/+1
Replace explicit casting by pointer to struct resource with specifier replacement to %pR to print the IO resource. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Drop useless assignmentAndy Shevchenko-1/+1
There is no need to assign ret variable in ->probe(). Drop useless assignment. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Correct amount of pinsAndy Shevchenko-6/+6
When we count from 0 it's possible to get into off-by-one error. That's what had happened to this driver. So, correct amount of pins and related typos in the code. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Use raw_spinlock for lockingAndy Shevchenko-14/+14
The Intel Lynxpoint pinctrl driver implements irqchip callbacks which are called with desc->lock raw_spinlock held. In mainline this is fine because spinlock resolves to raw_spinlock. However, running the same code in -rt we will get a BUG() asserted. This is because in -rt spinlocks are preemptible so taking the driver private spinlock in irqchip callbacks causes might_sleep() to trigger. In order to keep -rt happy but at the same time make sure that register accesses get serialized, convert the driver to use raw_spinlock instead. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Move GPIO driver to pin controller folderAndy Shevchenko-0/+482
Move Lynxpoint GPIO driver under Intel pin control umbrella for further transformation to a real pin control driver. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: baytrail: Reuse struct intel_pinctrl in the driverAndy Shevchenko-99/+87
We may use now available struct intel_pinctrl in the driver. No functional change implied. Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2019-12-13pinctrl: baytrail: Use local variable to keep device pointerAndy Shevchenko-9/+10
Use local variable to keep device pointer in order to increase readability of the driver. Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2019-12-13pinctrl: baytrail: Keep pointer to struct device instead of its containerAndy Shevchenko-29/+29
There is no need to keep pointer to struct platform_device, which is container of struct device, because the latter is what have been used everywhere outside of ->probe() path. In any case we may derive pointer to the container when needed. Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2019-12-13pinctrl: intel: Share struct intel_pinctrl for wider useAndy Shevchenko-34/+45
There are few drivers for Intel SoC GPIO which may utilize the same data structure to describe this IP. Share struct intel_pinctrl for wider user. Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2019-12-13pinctrl: intel: Use GPIO direction definitionsMatti Vaittinen-1/+4
Use new GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT when returning GPIO direction to GPIO framework. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: cherryview: Use GPIO direction definitionsMatti Vaittinen-1/+4
Use new GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT when returning GPIO direction to GPIO framework. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: baytrail: Use GPIO direction definitionsMatti Vaittinen-2/+2
Use new GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT when returning GPIO direction to GPIO framework. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2019-12-13pinctrl: baytrail: Move IRQ valid mask initialization to a dedicated callbackAndy Shevchenko-14/+9
There is a logical continuation of the commit 5fbe5b5883f8 ("gpio: Initialize the irqchip valid_mask with a callback") to split IRQ initialization to hardware and valid mask setup parts. Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2019-12-09pinctrl: baytrail: Group GPIO IRQ chip initializationAndy Shevchenko-1/+1
After commit 5ea422750a9f ("pinctrl: baytrail: Pass irqchip when adding gpiochip") the GPIO IRQ chip structure is being initialized under conditional when IRQ resource has been discovered. But that commit left aside the assignment of ->init_valid_mask() callback that is done unconditionally. For sake of consistency and preventing some garbage in GPIO IRQ chip structure group initialization together. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-09pinctrl: baytrail: Allocate IRQ chip dynamicAndy Shevchenko-10/+9
Keeping the IRQ chip definition static shares it with multiple instances of the GPIO chip in the system. This is bad and now we get this warning from GPIO library: "detected irqchip that is shared with multiple gpiochips: please fix the driver." Hence, move the IRQ chip definition from being driver static into the struct intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance. Fixes: 9f573b98ca50 ("pinctrl: baytrail: Update irq chip operations") Depends-on: ca8a958e2acb ("pinctrl: baytrail: Pass irqchip when adding gpiochip") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-09pinctrl: cherryview: Pass irqchip when adding gpiochipHans de Goede-23/+22
We need to convert all old gpio irqchips to pass the irqchip setup along when adding the gpio_chip. For more info see drivers/gpio/TODO. For chained irqchips this is a pretty straight-forward conversion. Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2019-12-09pinctrl: cherryview: Add GPIO <-> pin mapping ranges via callbackHans de Goede-11/+22
When IRQ chip is instantiated via GPIO library flow, the few functions, in particular the ACPI event registration mechanism, on some of ACPI based platforms expect that the pin ranges are initialized to that point. Add GPIO <-> pin mapping ranges via callback in the GPIO library flow. Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2019-12-09pinctrl: cherryview: Split out irq hw-init into a separate helper functionHans de Goede-18/+27
Split out irq hw-init into a separate chv_gpio_irq_init_hw() function. This is a preparation patch for passing the irqchip when adding the gpiochip. Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2019-12-09pinctrl: baytrail: Pass irqchip when adding gpiochipAndy Shevchenko-18/+24
We need to convert all old gpio irqchips to pass the irqchip setup along when adding the gpio_chip. For more info see drivers/gpio/TODO. For chained irqchips this is a pretty straight-forward conversion. Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Thierry Reding <treding@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Hans de Goede <hdegoede@redhat.com>
2019-12-09pinctrl: baytrail: Add GPIO <-> pin mapping ranges via callbackAndy Shevchenko-7/+14
When IRQ chip is instantiated via GPIO library flow, the few functions, in particular the ACPI event registration mechanism, on some of ACPI based platforms expect that the pin ranges are initialized to that point. Add GPIO <-> pin mapping ranges via callback in the GPIO library flow. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Hans de Goede <hdegoede@redhat.com>
2019-12-09pinctrl: baytrail: Update North Community pin listAndy Shevchenko-28/+28
Update North Community pin list to be more clear about pin functions. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>